To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C
Chapter 5. Block Diagram Figure 5-1 shows the CPU board components and their connectivity. Figure 5-1: Block Diagram Figure 5-2 shows the connectio
Chapter 6. User Circuitry 6.1. Switches There are four switches located on the CPU board. The function of each switch and its connection are shown i
Description Function Circuit Net Name Device Pin Fit for RS232 Remove for RS232 SCI1 Programming serial port TXD1 59 R31 R37, R32 SCI1 Progr
6.6. Option Links Table 6-5 below describes the function of the option links contained on this RSK board and associated with Serial Port Configuratio
Option Link Settings Reference Function Fitted Alternative (Removed) Related To R59 Application board interface Use PTRX of application board int
Option Link Settings Reference Function Fitted Alternative (Removed) Related To R116 Application board interface Use CS3n of application board in
Table 6-8 below describes the function of the option links associated with power source. The default configuration is indicated by BOLD text. Option
Option Link Settings Reference Function Fitted Alternative (Removed) Related To R220 Clock Oscillator External Clock Source On-board Clock Source
Option Link Settings Reference Function Fitted Alternative (Removed) Related To R235 MCU Mode MCU User Boot Mode enabled, also can be enabled b
Chapter 7. Modes This RSK supports Boot mode, User mode, MCU Extension Mode (ROM Active) and Single Chip mode. Details of programming the FLASH memo
Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang
Chapter 8. Programming Methods The board is intended for use with HEW and the supplied E10A debugger. Refer to H8SX/1648 Group Hardware Manual for d
Chapter 9. Headers 9.1. Microcontroller Headers Table 9-1 to Error! Reference source not found. show the microcontroller pin headers and their corre
J2 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 A1 37 2 A0 38 3 EMLE 39 4 PIN40 40 5 PIN41 41 6 IO_4 42 7 IO_5 43
J3 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 D7 73 2 UC_VCC 74 3 D8 75 4 D9 76 5 D10 77 6 D11 78 7 GROUND 79 8
J4 Pin Circuit Net Name Device Pin Pin Circuit Net Name Device Pin 1 TRSTn_SCK4 109 2 NC 3 TMS 111 4 NC 5 TDI 113 6 TCK 114 7 MD0 115 8
9.2. Application Headers Table 9-5 to Table 9-9 below show the standard application header connections.JA1 Pin Generic Header Name CPU board Signal
JA5 Pin Generic Header Name CPU board Signal Name Device Pin Pin Generic Header Name CPU board Signal Name Device Pin 1 AD4 AN4 124 2 AD5 AN5
JA3 Pin Generic Header Name CPU board Signal Name Device Pin Pin Generic Header Name CPU board Signal Name Device Pin 1 A0 A0 38 2 A1 A1 37
Chapter 10. Code Development 10.1. Overview Note: For all code debugging using Renesas software tools, the RSK board must be connected to a PC USB p
10.5. Memory Map Figure 10-1: Memory Map 27
Renesas Starter Kit for H8SX/1648User’s ManualUser’s ManualRev.1.00 2007.11RENESAS SINGLE-CHIP MICROCOMPUTERH8SX FAMILY
Chapter 11.Component Placement Figure 11-1: Component Placement – Top Layer 28
Chapter 12. Additional Information For details on how to use High-performance Embedded Workshop (HEW, refer to the HEW manual available on the CD or
Renesas Starter Kit for H8SX/1648 User's Manual Publication Date Rev.1.00 27.11.2007 Published by: Renesas Tec
1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanRenesas Starter Kit for H8SX/1648REG10J0079-0100User’s Manual
Table of Contents Chapter 1. Preface...
Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. Duplication of this d
Chapter 2. Purpose This RSK is an evaluation tool for Renesas microcontrollers. This manual describes the technical details of the RSK hardware. Th
Chapter 3. Power Supply 3.1. Requirements This RSK operates from a 5V power supply. A diode provides reverse polarity protection only if a current l
Chapter 4.Figure 4-1: Board Layout Board Layout 4.1. Component Layout The following diagram shows top layer component layout of the board. User s
4.2. Board Dimensions The following diagram gives the board dimensions and connector positions. All through hole connectors are on a common 0.1” grid
Commentaires sur ces manuels