Renesas Emulation Probe M306V8T-EPB Manuel d'utilisateur Page 48
- Page / 90
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
M306V8T-EPB User’s Manual 3. Usage (How to Use the Emulator Debugger)
REJ10J0777-0100 Rev.1.00 2005.08.01 Page 48 of 90
3.1.2 MCU Setting Dialog Box
MCU setting dialog box sets the information of the user system. It will be displayed after closing the Init dialog box.
(1) MCU tab
1. MCU Setting
Specifying the processor mode
Select the appropriate processor mode that suits your
system.
Specifying the bus width
When specifying memory expansion mode or
microprocessor mode, select “16-bit” for “External Data
Bus Width”.
Using or not using the memory space
expansion function
Specifies whether or not to use the memory space
expansion function when selecting memory expansion
mode or microprocessor mode. When using the memory
space expansion function, select “4MB Mode”. When
not, select “Normal Mode”
Using or not using the internal reserved
area expansion
Specifies whether or not to expand the internal reserved
area. Check this box if the internal reserved area
expansion bit (PM13) is “1”.
PM13=0:
Internal RAM area: 00400h--03FFFh
Internal ROM area: D0000h--FFFFFh
PM13=1:
Internal RAM area: 00400h--043FFh
Internal ROM area: 80000h--FFFFFh
Switching the CS2 area
Specifies CS2 area. When using the CS2 switching bit
(data block enable bit) (PM10) as “1”, check this box.
PM10 = 0: 09000h--26FFFh
PM10 = 1: 10000h--26FFFh
IMPORTANT
Notes on Selecting a Processor Mode:
When setting single-chip mode or memory expansion mode, the level of pin CNVSS of the MCU status should
be "L". The MCU status shows the pin level of the user system.
When setting microprocessor mode, the level of pin CNVSS of the MCU status should be "H".
When setting memory expansion mode or microprocessor mode, pins RDY* and HOLD* of the user system
should be "H".
When the user system is not connected, all modes are available.
M16C/6V8
- M306V8T-EPB 1
- Preface 3
- Important 4
- WARNING 6
- CAUTION 6
- WARNING 7
- Contents 9
- User Registration 11
- Terminology 12
- 1. Outline 13
- 1.3 System Configuration 15
- System status 16
- Target status 16
- IMPORTANT 17
- 1.4 Specifications 18
- 1.5 Operating Environment 19
- 2. Setup 20
- CAUTION 23
- 2.8 Self-check 28
- 2.10 Switch Settings 32
- ●EPB TRGT 34
- J1-4：GND 41
- J1-3：Oscillator output 41
- J1-2：GND 41
- J1-1：VCC 41
- INTERNAL 50
- 3.2 Editor (Source) Window 52
- 3.4 Trace Window 60
- 3.5 RAM Monitor Window 63
- 4. Hardware Specifications 64
- 4.2 Access Timing 65
- Write timing 66
- 4.4 Connection Diagrams 73
- Unit: mm 75
- 5. Troubleshooting 82
- 6. Maintenance and Guarantee 87
- User’s Manual 90
Produits connexes et manuels pour Matériel Renesas Emulation Probe M306V8T-EPB
Matériel Renesas 7542 Manuel d'utilisateur
(20 pages)
(20 pages)
Renesas REG10J0083-0100 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein Renesas REG10J0083-0100.
Wir stellen 1 PDF-Handbücher Renesas REG10J0083-0100 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Technical Information
Commentaires sur ces manuels