Renesas H8S2215R Manuel d'utilisateur

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

Chapter 5. Building the Tutorial Project The tutorial project build settings have been pre-configured in the tool-chain options. To view the tool ch

5.2. Connecting the debugger For this tutorial it is not necessary to provide an external power supply to the board, the power will be provided by t

• Select the Device on the RSK from the drop down list. • In the sub pane, select the kernel version that ends in ‘.RSK’. • Press <Next>. If

• Ensure that ‘USER Program Mode’ is selected. • Confirm that ‘Use Default’ is selected. • Press <Next>. • Confirm the default selection

Damage to the microcontroller can be sustained with incorrect settings. • Confirm the mode pin settings. • Press <Next>. • The following

5.3.1. Connecting To HMon We can now attempt to connect to the target device. • Press the Green ‘Connect’ Icon. HMon is able to discover the inter

• Confirm the settings shown and press <OK>. HMon will attempt to connect to the RSK. If it succeeds then the Output window in HEW will show

• Ensure ‘0x000D – 1 [Closed]’ is selected and click <OK>. On completion of the download HMon will automatically re-connect to the monitor an

Chapter 6. Downloading and Running the Tutorial Once the code has been built in HEW it needs to be downloaded to the RSK. Now that you are connected

We will now skip over the initialisation code and proceed to the main tutorial. • Open the file called ‘resetprg.c’ by double clicking it in the pr

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

• Right click on the ‘FlashLEDs();’ function and select ‘Go to cursor’. The code will run to the selected line and stop. A temporary breakpoint was

The code will now run to the infinite loop at the end of Main(). The user LEDs should now be flashing. You can modify the flashing rate by adjusting

• Press ‘Go’ to run the code from the current PC position. When the program stops you can see the modified string displayed on the second line of t

Chapter 7. Project Files 7.1. Standard Project Files The RSK tutorials are configured so that it is possible to provide the same tutorial code on m

7.1.2. Board initialisation code (Hwsetup.c / hwsetup.h) There are four common stages to the configuration of the microcontroller device. The code to

7.1.3. Main Tutorial Code (main.c / main.h) The main tutorial code is common to all tutorial projects. The display initialisation and string display

Chapter 8. Additional Information For details on how to use High-performance Embedded Workshop (HEW), refer to the HEW User manual available on the

Renesas Starter Kit for H8S2215R Tutorial Manual Publication Date Rev.1.00 12.01.2007 Published by: Renesas Techno

1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 JapanRenesas Starter Kit for H8S2215RREG10J0023-0100Tutorial Manual

Renesas Starter KitRSK H8S2215R Tutorial ManualUser’s ManualRev.1.00 2007.01RENESAS SINGLE-CHIP MICROCOMPUTER

Table of Contents Chapter 1. Preface...

Chapter 1. Preface Cautions This document may be, wholly or partially, subject to change without notice. All rights reserved. No one is permitted t

Chapter 2. Introduction This manual is designed to answer, in tutorial form, the most common questions asked about using a Renesas Starter Kit (RSK)

Chapter 3. Tutorial Project Workspace The workspace includes all of the files for two build configurations. The tutorial code is common to both the

Chapter 4. Project Workspace 4.1. Introduction HEW is an integrated development tool that allows the user to write, compile, program and debug a sof

• Click OK to start the RSK Project Generator wizard. The next dialog presents the example projects available. Choose the Tutorial code which will b