Renesas SuperH SH7343 Informations techniques Page 43
- Page / 204
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Target interface (SH7206) Jun. 1, 2010 (Third Edition)
Mictor connector
Signals
CPU Pin No.
*2
CPU Pin No.
*2
Pin
No.
Signal
Input/
Output
*1
LQFP-176
Pin
No.
Signal
Input/
Output
*1
LQFP-176
1 N.C. 2 N.C.
3 GND (ASEMD)
*3
(Input) (119) 4 N.C.
5 GND (CON)
*6
(Output) 6 AUDCK Output 75/134
7 N.C. 8
ASEBRKAK
/
ASEBRK
Input/Output 104
9 RES Output 37 10 N.C.
11 TDO Output 120 12 VCC_AUD
*4
Output
13 N.C. 14 VCC
*5
Output
15 TCK Input 110 16 N.C.
17 TMS Input 116 18 N.C.
19 TDI Input 112 20 N.C.
21 TRST Input 111 22 N.C.
23 N.C. 24 AUDATA3 Output 80/137
25 N.C. 26 AUDATA2 Output 86/138
27 N.C. 28 AUDATA1 Output 82/139
29 N.C. 30 AUDATA0 Output 84/140
31 N.C. 32 AUDSYNC Output 132/167
33 N.C. 34 N.C.
35 N.C. 36 N.C.
37 N.C. 38 N.C.
・ For the pin where stated as N.C. in the table, leave the signal unconnected.
*1: Input/output is based on the target system.
*2: 2 routings of AUD ports are available. Choose either of them.
*3: To debug,
ASEMD pin needs to be brought to Low state.
Shown in the target connection reference diagram is the circuit that brings ASEMD pin to Low state when you connect ASEMD signal to the connector for
debugger. If you do not connect ASEMD signal to Pin No. 3 of the connector for debugger, the circuit that sets ASEMD pin by switch circuit will do. However, in
such case, do not connect ASEMD pin to Pin No. 3 of the connector for debugger, but connect Pin No. 3 of connector for the debugger to GND.
*4: For VCC_AUD, the power same as the voltage level at which AUD signal of CPU works is to be connected. Connect the AUD signal to I/O
power of CPU.
*5: For VCC, the power same as the voltage level at which HUDI signal of CPU works is to be connected. Connect the HUDI signal to I/O power
of CPU.
*6: By detection of GND on the target system side, whether the target system is connected or not is determined.
Target connection reference diagram
Mictor connector specifications
Recommended connector
Manufacturer AMP
Model Mictor connector
2-767004-2 / 767054-1 / 767061
(Top view on the target board)
(For detailed dimensions of the connector,
refer to the documentation by manufacturer of the connector.)
*Please look at the pin configuration diagram above and make
sure that the connector is in the right direction before connecting.
Please check the pin number in the signal table above and make sure
the signal and the pin numbers match.
*1: RES, which is connected to Pin No. 9 of the connector for debugger, is the signal that debugger uses for monitoring the state of RES pin of
CPU.
- Technical Information 1
- Document change history 2
- AUD probe 5
- Mictor probe 5
- HUDI cable 5
- ■ SH7047F 7
- ■ SH7055F 10
- ■ SH7055SF 12
- ■ SH7058F 14
- ■ SH7058SF/SH7059F 16
- (SH7058SF/SH7059F) 17
- ■ SH7144F/SH7145F 21
- history (SH7144F/SH7145F) 23
- ■ SH7146F 24
- ■ SH7149F 26
- (SH7149F) 28
- ■ SH7606 29
- ■ SH7618/SH7618A 31
- Also, added CPU SH7618A 32
- ■ SH7619 33
- SH2-DSP 35
- ■ SH7615 36
- ■ SH7616 38
- ■ SH7206 41
- ■ SH7211F 45
- ■ SH7243F/SH7285F/ SH7286F 49
- (Output) 52
- (SH7243F/SH7285F/ SH7286F) 54
- SH2A-FPU 55
- ■ SH7201 56
- (SH7201) 59
- ■ SH7203 60
- ■ SH7261 64
- ■ SH7262/SH7264 68
- ■ SH7263 72
- SH2A-DUAL 78
- ■ SH7205 79
- ■ SH7265 83
- ■ SH7705 88
- ■ SH7706 91
- ■ SH7709S 94
- SH3-DSP 97
- ■ SH7290(SH-Mobile1) 98
- ■ SH7294(SH-MobileJ) 101
- (SH7294(SH-MobileJ)) 103
- ■ SH7300(SH-MobileV) 104
- ■ SH7710 107
- ■ SH7712 110
- ■ SH7713 113
- ■ SH7720/SH7721 116
- Also, added CPU SH7721 118
- ■ SH7727 119
- ■ SH7729 122
- ■ SH7729R 125
- SH4AL-DSP 128
- ■ SH7343(SH-Mobile3AS) 129
- (SH7343(SH-Mobile3AS)) 131
- ■ SH7354(SH-MobileL3V) 132
- ■ SH7722(SH-MobileR) 135
- (SH7722(SH-MobileR)) 137
- ■ SH7750R/SH7750S 139
- BGA-292 140
- ■ SH7751/SH7751R 141
- ■ SH7760 144
- ■ SH7723(SH-MobileR2) 148
- ■ SH7730 152
- ■ SH7763 156
- ■ SH7764 159
- ■ SH7770 163
- (SH7770) 164
- ■ SH7774 165
- (SH7774) 166
- ■ SH7780 167
- ■ SH7781 170
- ■ SH7785 172
- Second Edition Jun. 1, 2010 174
- ・ Mictor connector 174
- PALMiCE3 HUDI140 model 175
- Hardware Manual 175
- Table of Contents 177
- Chapter 1 Getting Started 178
- 1.1 Introduction 179
- Product Composition Contents 180
- 1.3 Connection structure 181
- Chapter 2 182
- HUDI140 model specifications 183
- 2.3.1 RSTOUT probe 184
- How revision sticker reads 185
- 3.1 Introduction 187
- 3.2 H-UDI interface 187
- 3.2.5 RSTOUT signal 188
- CM845(C)1101 189
- PALMiCE3 AUD360 model 190
- AUD360 model specifications 198
- 3.2 AUD interface 202
- 3.2.4 RSTOUT signal 203
- Aug. 2011 Fourth Edition 204
- CM884(D)1108 204
Produits connexes et manuels pour Mise en réseau Renesas SuperH SH7343
Mise en réseau Renesas TM V.3.20A Spécifications
(762 pages)
(762 pages)
(18 pages)
Mise en réseau Renesas R8C/Tiny Series Manuel
(199 pages)
(199 pages)
Mise en réseau Renesas M16C FAMILY Manuel
(11 pages)
(11 pages)
Renesas REG10J0083-0100 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein Renesas REG10J0083-0100.
Wir stellen 1 PDF-Handbücher Renesas REG10J0083-0100 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Technical Information
Commentaires sur ces manuels