Renesas FP-112B Informations techniques

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

IVSAFETY PAGEREAD FIRST• READ this user's manual before using this user system interface cable.• KEEP the user's manual handy for future ref

VWARNINGObserve the precautions listed below. Failure to do sowill result in a FIRE HAZARD and will damage the usersystem and the emulator product or

iPrefaceThank you for purchasing this user system interface cable (HS7042ECH61H) for the Hitachi’soriginal microcomputer SH7040 series.The HS7042ECH61

iiContentsSection 1 Configuration...1Section 2 Connection Procedures .

1Section 1 ConfigurationCAUTIONUse an IC149-112C15333-0B socket (manufactured byYAMAICHI ELECTRONICS Co., Ltd.) for the FP-112 package IC socket on

2Table 1 lists the HS7042ECH61H components. Please make sure you have all of thesecomponents when unpacking.Table 1 HS7042ECH61H ComponentsNo. Compon

3Section 2 Connection Procedures2.1 Connecting User System Interface Cable to Emulator StationWARNINGObserve the precautions listed below. Failure to

4Figure 2 Connecting User System Interface Cable to Emulator Station

52.2 Connecting User System Interface Cable to User SystemWARNINGAlways switch OFF the user system and the emulatorproduct before the USER SYSTEM INTE

62.2.4 Fastening Cable HeadCAUTION1. Use a Phillips-type screwdriver whose head matchesthe screw head.2. The tightening torque must be 0.098 N•m or le

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

7Fasten the user system interface cable head to the IC socket for an FP-112 package on the usersystem with the four screws (M2 x 12 mm; with four flat

82.2.5 Fastening Cable BodyConnect the cable body to the cable head.Figure 4 Fastening Cable Body

92.3 Recommended Dimensions for User System Mount PadFigure 5 shows the recommended dimensions for the mount pad (footprint) for the user systemwith a

102.4 Dimensions for User System Interface Cable HeadThe dimensions for the user system interface cable head are shown in figure 6.Figure 6 Dimensions

112.5 Resulting Dimensions after Connecting User System Interface CableThe resulting dimensions, after connecting the user system interface cable head

12Section 3 Installing the MCU to the User SystemCAUTION1. Check the location of pin 1 before inserting.2. Use a Phillips-type screwdriver whose head

13Figure 8 Installing MCU to User System

14Section 4 Verifying Operation1. When using the E6000 emulator for the SH7040 series, turn on the emulator according to theprocedures described in th

15Section 5 Notice1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cablehead before inserting the cable h

Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp.The semiconductor operati

CautionsKeep safety first in your circuit designs!1. Renesas Technology Corporation puts the maximum effort into making semiconductor products better

SH7042 FP-112User System Interface Cable(HS7042ECH61H) for E6000 EmulatorUser’s ManualUser’s Manual Rev.1.0 2002.07

Cautions1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’spatent, copyright, trademark, or other intellec

IIMPORTANT INFORMATIONREAD FIRST• READ this user's manual before using this user system interface cable.• KEEP the user's manual handy for f

IILIMITED WARRANTY Hitachi warrants its user system interface cables to be manufacturedin accordance with published specifications and free from d

IIIState Law:Some states do not allow the exclusion or limitation of implied warranties or liability forincidental or consequential damages, so the ab