Renesas M32C/87 Manuel d'utilisateur Page 25
- Page / 104
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
M30870T-EPB User’s Manual 2. Setup
REJ10J0482-0300 Rev.3.00 February 16, 2006
2.6.4 LED Display When the Emulator Starts Up Normally
Figure 2.4 shows upper panel LED lighting status when the emulator started up properly. Check it when starting up the
emulator system.
POWER
CLOCK
RUN
RESET
WARNING
TARGET
STATUS
SYSTEM
STATUS
POWER
SAFE
ERROR
: ON
: OFF
: Flashing
- If this LED does not light, check the voltage of the user system.
- Check power is supplied to all the power terminals.
- When the user system is not connected, this LED does not light.
Figure 2.4 LED display when the power turned on PC7501
IMPORTANT
Note on Memory Expansion and Microprocessor Modes:
To use memory expansion or microprocessor mode, be sure to set pins RDY*, HOLD* and NMI* so that they
are not active at start-up. Otherwise the emulator system will not start up correctly.
Note on CLOCK LED:
If CLOCK LED does not turn on, check the following:
(1) Immediately after starting PC7501 (before starting the emulator debugger)
Check if the oscillation circuit within the PC7501 emulator main unit oscillates normally.
(2) After starting the emulator debugger (after setting the Init dialog box)
Check the oscillation circuit set in the Init dialog box oscillates normally.
Page 25 of 104
- M30870T-EPB 1
- Preface 3
- Important 4
- Page 5 of 104 5
- WARNING 6
- CAUTION 6
- WARNING 7
- Contents 9
- Page 10 of 104 10
- User Registration 11
- Terminology 12
- 1. Outline 13
- 1.3 System Configuration 14
- Page 15 of 104 15
- 1.4 Specifications 17
- 1.5 Operating Environment 18
- 2. Setup 19
- Page 20 of 104 20
- Page 21 of 104 21
- IMPORTANT 24
- 2.8 Self-check 27
- 2.10 Setting Switches 38
- Page 39 of 104 39
- Page 40 of 104 40
- Page 41 of 104 41
- Page 44 of 104 44
- J1-4: GND 46
- J1-3: Oscillation output 46
- J1-2: GND 46
- J1-1: VCC 46
- Page 47 of 104 47
- M30870T-EPBM REV.B 48
- 3. Usage (Emulator Debugger) 50
- Page 51 of 104 51
- Page 53 of 104 53
- Page 54 of 104 54
- Page 55 of 104 55
- Page 56 of 104 56
- Page 61 of 104 61
- 3.3 Program Window 62
- Page 64 of 104 64
- (2) Click the Come button 65
- Page 66 of 104 66
- Page 67 of 104 67
- Page 68 of 104 68
- Page 70 of 104 70
- 3.5 Trace Window 71
- Page 72 of 104 72
- Page 73 of 104 73
- Page 74 of 104 74
- Page 75 of 104 75
- 3.6 RAM Monitor Window 76
- Page 77 of 104 77
- Page 78 of 104 78
- 4. Hardware Specifications 79
- 4.3 Connection Diagrams 83
- ON ON resistor 85
- 4.4 External Dimensions 86
- Page 87 of 104 87
- Page 88 of 104 88
- 5. Troubleshooting 95
- Page 96 of 104 96
- Page 97 of 104 97
- Page 98 of 104 98
- Page 99 of 104 99
- 6. Maintenance and Guarantee 100
- CAUTION 101
- Page 102 of 104 102
- User's Manual 104
Produits connexes et manuels pour Non Renesas M32C/87
Non Renesas M3A-HS19 Manuel d'utilisateur
(72 pages)
(72 pages)
Non Renesas H8SX/1651 Manuel d'utilisateur
(36 pages)
(36 pages)
Non Renesas SH2/7137 Manuel d'utilisateur
(36 pages)
(36 pages)
Non Renesas M32C/88 Manuel d'utilisateur
(100 pages)
(100 pages)
Non Renesas SH7085 Manuel d'utilisateur
(48 pages)
(48 pages)
Non Renesas M30620T-CPE Manuel d'utilisateur
(52 pages)
(52 pages)
Non Renesas M302N2T-PRB Manuel d'utilisateur
(38 pages)
(38 pages)
Non Renesas H8/3694 Manuel d'utilisateur
(30 pages)
(30 pages)
Renesas REG10J0083-0100 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Nein Renesas REG10J0083-0100.
Wir stellen 1 PDF-Handbücher Renesas REG10J0083-0100 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Technical Information
Commentaires sur ces manuels