Renesas FLASH Development Toolkit 3.07 Manuel d'utilisateur télécharger pdf (Page 23)

CellCom/FreeSpeak Firmware Update Procedures

Rev: 6.05 VGC Part No.- 810372Z-MAN-6 Page 23 of 49

Is the

download LED on the

mainboard flashing at a 1:1

ON to OFF ratio.

Downloading takes

approximately 10

minutes.

Yes

Is the

download LED on the

mainboard continuously

flashing at a 1:9 ON to OFF

ratio.

The download failed. Check cables

and terminal settings again. After 3

failures check if the

RAM and PROM

require upgrading.

1. Stop the download on the Terminal

Emulator

2. Power cycle the Basestation.

Yes

Select from the menus

(TRANSFER -> SEND TEXT FILE).

Select the new basestation file

710806Z.4. You will find this file on

the CD in directory

\Firmware\Base station\APP\and click

open.

NOTE: Hyper-terminal does not show a

progress bar.

Does

.A

.A



and off.

1.Power Cycle the base.

2.Install the new cellcom toolkit. 3.Load

the map backed up earlier using the new



upgrades.

4.Save the new map under a different

name (click Save As).

5.Send the new map to the basestation.

NOTE:The upgraded Map is not

compatible with 1.5.6 or ealier versions.

FINISHED

1. Power Down the base and remove the power cable

2. Remove the lid and move the jumper next to the battery to link pins 2&3.

3. Wait 5 seconds and move the jumper back to its original place.

4. Set dipswitches 1 and 2 3 and 4 .

5. Reconnect the Power cable and Power On the Basestation for 30 Seconds.

6. Power Down the base and set dipswitches 1, 2, 3 and 4 .

7. Power Up the base

8. Power Down the base and set dipswitches 1, 2, 3, and 4 

9. Power up the base and connect the PD4010(Z) cable to a PC.

10. The download LED on the mainboard will flash at a 1:9 ON to OFF ratio.

HYPER-TERMINAL IMAGE DOWNLOAD

1. Baud=38400, Data=8, Parity=Even, Stop=1, Flow=None

2. 

Terminal Keys,

Ctrl+H,

Emulation=TTY.

Terminal ID=ANSI

3. .

4. 

5. In the "ASCII Setup" ensure "Send Line Ends With Line Feeds" is checked, set everything else to 0 or unchecked.

you have hyper-

terminal on your

PC?

Yes

Install a Terminal emulator and

configure it to its equivalent

Hyperterminal settings given in the

next step

(for example install S4DRV)

START 2

CELLCOM-10 / FREESPEAK-10

BASESTATION FIRMWARE

UPGRADE GUIDE

**Download LED

(Top LED out of the group of 3)

Seen only on earlier base station

hardware versions

2 

Xilinx FPGA image file called

2FPGA2_1.

You will find this file on the CD in directory

\Firmware\Base station\

After the Basestation has reset. Check the

FPGA Software version from the front panel

SYSTEM->INFO menu. .

Enter v2.0 Passcode

5.1.1 Upgrade from Configuration Editor

- Connect the PC to the Basestation using an Ethernet

Crossover cable or similar

- Open the Configuration Editor

- 

- 

- 

- Select the File to be downloaded (this can be a utility file, such

         

CONSULT THE BASESTATION FIRMWARE UPGRADE

GUIDE FLOW DIAGRAM FOR INFORMATION ON FILE

LOADING ORDER

- 

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 48 49

Commentaires sur ces manuels

Pas de commentaire

Renesas FLASH Development Toolkit 3.07 Manuel d'utilisateur Page 23

Commentaires sur ces manuels

Produits connexes et manuels pour Non Renesas FLASH Development Toolkit 3.07